预应力钢梁体外索的张力增量分析

将预应力钢梁看作梁与索的组合结构,充分考虑了二者之间的相互作用．利用变分原理推导出在外荷载作用下,体外索张力增量的计算公式,并通过预应力钢梁模型试验对计算结果进行了验证．     

Effects of oxidation and surface roughness on contact angle

Contact angle is known to be a parameter that effects boiling. This study was undertaken to measure contact angle of high and low surface tension fluids on copper and aluminum surfaces.Data were taken for polished, oxidized, and rough surfaces. A simple, yet fairly accurate method of measuring the static equilibrium contact angle of a solid/liquid interface is presented. The principles of a line light source and tilting plate were modified and then combined in the design of this apparatus. The angles obtained and their variation with the solid surface properties were in good agreement with previously published data. The contact angle of distilled water o of the organic fluids and refrigerants tested were in the range of 2–5°. Roughness and oxidation reduce the contact angle. If the depth of the roughness is less than 0.5 μm contact angle. The apparatus is fairly simple in construction, is inexpensive, and has good reproductibity. The measured angles were then compared to those measured with the sessile drop method.     

液体表面张力系数的实验研究

改变液体的浓度可以调控液体的表面张力系数,各种形状膜架的挂膜时间与液体表面张力系数存在着一定的关系,本文对于这两个方面进行了实验研究,得出了相应的结果.此外,溶液的温度和空气的流动对挂膜时间都会产生影响.     

Generation of Silicone Poly‐HIPEs with Controlled Pore Sizes via Reactive Emulsion Stabilization

Macrocellular silicone polymers are obtained after solidification of the continuous phase of a poly(dimethylsiloxane) emulsion, which contains poly(ethylene glycol) drops of sub‐millimetric dimensions. Coalescence of the liquid template emulsion is prohibited by a reactive blending approach. The relationship is investigated in detail between the interfacial properties and the emulsion stability, and micro‐ and millifluidic techniques are used to generate macrocellular polymers with controlled structural properties over a wider range of cell sizes (0.2–2 mm) and volume fractions of the continuous phase (0.1%–40%). This approach could easily be transferred to a wide range of polymeric systems.

     

Phase and Interfacial Tension Behavior of Certain Model Gas Condensates: Measurements and Modeling

This contribution reports on the phase and interfacial tension behavior of some model high-temperature–high-pressure gas condensates. On the one hand these types of gas condensate are becoming a subject of major interest for the oil industry, while on the other their phase and interfacial tension behavior have not been very well studied. For two different model gas condensates, both composed of the three n-alkanes, methane, butane, and decane, experimental results on their fluid phase behavior have been obtained in the temperature region 270 < T (K) < 490 and up to pressures as high as 24 MPa. Also, critical points of the two mixtures have been determined experimentally. Both mixtures show an extended retrograde region. Using the Peng–Robinson equation of state, the phase behavior of the two mixtures was modeled. In addition, the interfacial tension behavior of the model gas condensates was modeled. For that purpose, the Cahn–Hilliard theory was applied in combination with the Peng–Robinson equation of state. Satisfactory results were obtained.     

基于移动粒子半隐式法的表面张力模拟

采用移动粒子半隐式法(MPS)模拟了受表面张力影响的自由面流动。表面张力的计算采取了一种较适合于MPS方法的表面自由能模型。方形液滴振荡和射流断裂的模拟结果分别与理论分析和试验结果一致,同时进行了三维射流注水模拟,从而验证了MPS方法结合该表面张力模型可以有效、方便地进行自由面流动中表面张力现象的模拟。     

The stick-slip problem for a round jet

Summary The stick-slip problem for a round jet studied in Part I gives a good approximation for the swell of a low speed jet when the surface tension is large but it fails when the surface tension is small. In this paper a new stick-slip problem (II) is defined and solved using matched eigenfunction expansions. The new problem reduces to that solved in Part I when the surface tension is large and gives good results in the case of zero and small surface tension.With 18 figures     

Structural Stability of Unsteadily Accelerated Liquid Pistons

The possibility of the fragmentation of a liquid piston moving with variable acceleration, due to air jets forming on its free surface and penetrating inward, is established experimentally. The liquid piston acceleration regimes in which air jets capable of penetrating into the liquid are formed from initial perturbations on its free surface are theoretically analyzed.     

实现金属环动态拉伸的电磁加载技术研究

描述了实现金属环动态拉伸的电磁膨胀环实验方法,改进了快速放电和短路开关两个实现自由膨胀的关键问题,为研究材料本构关系、动态断裂和破碎提供了一条简单而实用的加载途径。主回路电流由Rogowski线圈测量获得,金属环的膨胀速度由狭缝扫描相机测量得到,并由电动力学方程可计算出金属环中的流动应力、应变、应变率以及温升等动态力学参数。